-
Add to Cart The item has been added Allen & Heath
Allen & Heath CC-STN Desk Stand for CC-7 and CC-10OverviewThe CC-STN is the desktop stand for Allen & Heath's CC-7 and CC-10 Custom Control touch panels. It holds the panel at a comfortable viewing angle on a desk, lectern, bar or control booth, so...$399.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath CC-BRK Wall / Glass Mount Bracket for CC-7 and CC-10OverviewThe CC-BRK is Allen & Heath's wall and glass mounting bracket for the CC-7 and CC-10 Custom Control touch panels. It lets you fix a panel to a wall beside a door, on a column or onto a glass...$399.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath IP8 Wall Mount KitOverviewThe IP8-MOUNT kit fixes an IP8 remote controller into a wall, plinth, podium or piece of furniture. The IP8 slides into the bracket and is held with six screws through its threaded inserts,...$199.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath IP6 / ME Wall Mount KitOverviewThis kit mounts an IP6 remote controller, ME-1 or ME-500 personal mixer into a wall, so a controller in a meeting room or a personal mixer in a choir loft or rehearsal room stays put. The...$199.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath DT-SMK Surface Mount Kit for DT02 and DT20OverviewThe DT-SMK adds surface mounting ears to a standard DT02 or DT20, so you can screw the interface under a desk, inside a lectern or on a wall beside a powered speaker. These are the same ears...$99.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath DT-RK19 Rack Kit for DT02, DT20 and DT22OverviewThe DT-RK19 mounts one or two of Allen & Heath's compact DT interfaces in a single 1U space of a 19 inch rack, in any combination of DT02, DT20 and DT22, facing front or rear. It is the clean...$249.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath DX88-P 1U 19 Inch Rack Mount KitOverviewThe optional rack kit for the DX88-P. It fits up to two DX88-P units side by side in a single 1U space of a 19 inch rack, and lets you blank off one half if only one unit is installed. A&H...$199.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath DX Hub / GPIO 19 Inch Rack Kit (FULLU-RK19)OverviewThis kit rack mounts Allen & Heath's half width 1U interfaces in a standard 19 inch rack. It takes one or two units on the left or right side, front or rear facing, in any combination of two...$199.00 -
Add to Cart The item has been added DiGiCo
DiGiCo D2-Rack Blank PlateOverviewThe D2-Rack Blank Plate covers an unused output option slot on a DiGiCo D2-Rack. The D2-Rack has two 8 channel output option slots, and any slot without a card should be covered to keep dust...$180.00 -
Add to Cart The item has been added DiGiCo
DiGiCo D-Rack 19 Inch Rack Mount Ears PairOverviewThese brackets let you mount a DiGiCo D-Rack in a standard 19 inch rack. Out of the box the D-Rack is a floor standing stage box; with the ears fitted it takes 7U and can be built into a road...$245.00 -
Add to Cart The item has been added DiGiCo
DiGiCo D-Rack Isolator KitOverviewThe D-Rack Isolator Kit is the isolating transformer for the D-Rack's RJ45 CAT5 MADI input. DiGiCo fits an isolating transformer on this input as standard to break ground paths between the...$480.00 -
Add to Cart The item has been added Allen & Heath
Allen & Heath AB168 / DX168 / DT168 Padded Carry BagOverviewA padded carry bag sized for Allen & Heath's portable 16 x 8 stagebox chassis. It protects the AB168, DX168 or DT168 in the van and between venues, and keeps the XLR panel clear of knocks...$149.00
Console Accessories
Cases, dust covers, rack kits, brackets and holders for DiGiCo and Allen & Heath consoles and I/O.